A pool table is an elegant design used for indoor sports rooms and patios. The game of pool is played as a way of spending leisure time with friends and family. If the tables were to be made of materials that are durable, they can last around twenty years with less maintenance. The most vulnerable component of the structure is the felt. In consideration of pool table refelting Denver residents should know the procedure.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
After the choice of color, the rails need to be removed using a crescent wrench. This is done by removing the bolts that attach the rails. Rails are also always covered by the felt and need to be re-felted too. This explains the need to buy extra material. Rails are carefully placed on the floor close to the table so that there is no mistake when reattaching them.
A staple remover is used when removing the old material. It is used to out staples which are at the felt edges. All felt should be removed from the table so that the newly placed one is perfectly fitted. The one that has been removed can be put in a thrash bag to be disposed later.
The new felt needs to be carefully placed while taking care to inspect that no damaged are done and that there are no stains. A sharp scissor should then be used to cut it, using the border of the table to guide you. Some felt is left over to be used to re-felt the rails.
After the cut has been made, the felt is attached to the top of the table using a stapler. The stapling should start at the mid portion of one end of the felt before the right and left edges are stapled. After this, you should go to the opposite end and tightly pull the felt. It is then stapled in the same way as the previous side.
The side edges will then need to be stapled. You should ascertain that the staples are at an equal distance from each other and lined up in the correct way. For the pockets, 3 slits should be cut on every pocket before wrapping and stapling the felt on the edges of the pockets. The felt is tightly pulled prior to stapling.
Finally, the structure is reassembled. Rails will be attached to their original positions using a crescent wrench. The pocket lines are inserted and the table is ready for use.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
After the choice of color, the rails need to be removed using a crescent wrench. This is done by removing the bolts that attach the rails. Rails are also always covered by the felt and need to be re-felted too. This explains the need to buy extra material. Rails are carefully placed on the floor close to the table so that there is no mistake when reattaching them.
A staple remover is used when removing the old material. It is used to out staples which are at the felt edges. All felt should be removed from the table so that the newly placed one is perfectly fitted. The one that has been removed can be put in a thrash bag to be disposed later.
The new felt needs to be carefully placed while taking care to inspect that no damaged are done and that there are no stains. A sharp scissor should then be used to cut it, using the border of the table to guide you. Some felt is left over to be used to re-felt the rails.
After the cut has been made, the felt is attached to the top of the table using a stapler. The stapling should start at the mid portion of one end of the felt before the right and left edges are stapled. After this, you should go to the opposite end and tightly pull the felt. It is then stapled in the same way as the previous side.
The side edges will then need to be stapled. You should ascertain that the staples are at an equal distance from each other and lined up in the correct way. For the pockets, 3 slits should be cut on every pocket before wrapping and stapling the felt on the edges of the pockets. The felt is tightly pulled prior to stapling.
Finally, the structure is reassembled. Rails will be attached to their original positions using a crescent wrench. The pocket lines are inserted and the table is ready for use.
No comments:
Post a Comment